Máy hiện sóng Hantek DSO5202P 2 kênh dải đo 200Mhz - Digital Oscilloscope DSO5202P 200MHZ

Mã sản phẩm: HH002672

Thương hiệu: HANTEK Loại: (Đang cập nhật ...)

8.000.000 VNĐ
Máy hiện sóng Hantek DSO5202P 2 kênh dải đo 0-200Mhz Bảo hành 12 tháng. Miễn phí vận chuyển toàn quốc 1. Feature 200MHz bandwidths 1GSa/s Real Time sample rate Large (7.0-inch) color display,WVGA(800x480) Record length up to 40K Trigger mode: edge/pulse width/line select...
chinh-sach
Linh Kiện Việt Nam bán đúng giá công khai trên web.
chinh-sach
Đổi trả trong 48h, thủ tục đơn giản.

Máy hiện sóng Hantek DSO5202P 2 kênh dải đo 0-200Mhz

Bảo hành 12 tháng.  Miễn phí vận chuyển toàn quốc

1. Feature

  • 200MHz bandwidths
  • 1GSa/s Real Time sample rate
  • Large (7.0-inch) color display,WVGA(800x480)
  • Record length up to 40K
  • Trigger mode: edge/pulse width/line selectable video/slop/overtime etc.
  • USB host and device connectivity, standard
  • Multiple automatic measurements
  • Four math functions, including FFTs standard
  • Provides software for PC real-time analysis
  • VGA Optional
  • 2. Specifications

    Model DSO5202P
    Acquisition
    Sample Rate Real-Time Sample: 1GS/s
    Acquisition Modes  
    Normal Normal data only
    Peak Detect High-frequency and randon glith capture
    Average Wavefom Average, selectable 4,8,16,32,64,128
    Inputs
    Inputs Coupling AC, DC, GND
    Inputs Impendance 1MΩ±2% ‖20pF±3pF
    Probe Attenuation 1X, 10X
    Supported Probe Attenuation Factor 1X, 10X, 100X, 1000X
    Maximum Input Voltage CAT I and CAT II: 300VRMS (10×), Installation Category;
    CAT III: 150VRMS (1×);
    Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur.
    Horizontal System
    Sample Rate Range 500MS/s--1GS/s
    Waveform Interpolation (sin x)/x
    Record Length 40K
    SEC/DIV Range 2ns/div to 40s/div
    Sample Rate and
    Delay Time Accuracy
    ±50ppm(at over any ≥1ms time interval)
    Position Range 2ns/div to 10ns/div;  (-4div x s/div) to 20ms;
    Delta Time Measurement Accuracy 
    (Full Bandwidth)
    Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns);
    >16 averages:± (1 sample interval + 100ppm × reading + 0.4ns);
    Sample interval = s/div ÷ 200
    Vertical System
    Vertical Resolution 8-bit resolution, all channel sampled simultaneously
    Position Range 2mV/div to 10V/div
    Bandwidth 200MHz
    Rise Time at BNC( typical) 1.8ns
    Analog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled 2mV/div to 20mV/div, ±400mV;  50mV/div to 200mV/div, ±2V
    500mV/div to 2V/div, ±40V; 5V/div, ±50V
    Math +, -, *, /, FFT
    FFT Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman;
    1024 sample point
    Bandwidth Limit 20MHz
    Low Frequency Response (-3db) ≤10Hz at BNC
    DC Gain Accuracy ±3% for Normal or Average acquisition mode, 5V/div to 10mV/div;
    ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div
    DC Measurement Accuracy, 
    Average Acquisition Mode
    When vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected; 
    When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/div
    Volts Measurement Repeatability, 
    Average Acquisition Mode
    Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions
    Trigger System
    Trigger Types Edge, Video, Pulse, Slope, Over time, Alternative
    Trigger Source CH1, CH2, EXT, EXT/5, AC Line
    Trigger Modes Auto, Normal, Single
    Coupling Type DC, AC, Noise Reject, HF Reject, LF Reject
    Trigger Sensitivity
    (Edge Trigger Type)
    DC(CH1,CH2):
    1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full;
    DC(EXT): 
    200mV from DC to 100MHz; 350mV from 100MHz to 200MHz;
    DC(EXT/5):       
    1V from DC to 100MHz;1.75V from 100MHz to 200MHz;       
    AC: Attenuates signals below 10Hz;
    HF Reject: Attenuates signals above 80kHz 
    LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz
    Trigger Level Range CH1/CH2: ±8 divisions from center of screen; 
    EXT: ±1.2V;
    EXT/5:±6V
    Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥20ns CH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen;
    EXT: ± (6% of setting + 40mV);
    EXT/5: ± (6% of setting + 200mV);
    Set Level to 50%(typical) Operates with input signals ≥50Hz
    Video Trigger  
    Video Trigger Type  CH1, CH2: Peak-to-peak amplitude of 2 divisions;
    EXT: 400mV;
    EXT/5: 2V
    Signal Formats and Field Rates, Video Trigger Type Supports NTSC, PAL and SECAM broadcast systems for any field or any line
    Holdoff Range 100ns ~ 10s
    Pulse Width Trigger  
    Pulse Width Trigger Mode Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse
    Pulse Width Trigger Point Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level.
    Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.
    Less than: The trigger point is the trailing edge.
    Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width
    Pulse Width Range 20ns ~ 10s
    Slope Trigger  
    Slope Trigger Mode Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope
    Slope Trigger Point Equal: The oscilloscope triggers when the waveform slope is equal to the set slope.
    Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope.
    Less than: The oscilloscope triggers when the waveform slope is less than the set slope.
    Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.
    Time Range 20ns ~ 10s
    Overtime Trigger  
    Over Time Mode Rising edge or Falling edge
    Time Range 20ns ~ 10s
    Alternative Trigger  
    Trigger on CH1 Internal Trigger: Edge, Pulse Width, Video, Slope
    Trigger on CH2 Internal Trigger: Edge, Pulse Width, Video, Slope
    Trigger Frequency Counter
    Readout Resolution 6 digits
    Accuracy (typical) ±30ppm (including all frequency reference errors and ±1 count errors)
    Frequency Range AC coupled, from 4Hz minimum to rated bandwidth
    Signal Source Pulse Width or Edge Trigger modes: all available trigger sources
    The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed.
    Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time.
    Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity.
    Video Trigger mode: The Frequency Counter does not work.
    Measure
    Cursor Measurement Voltage difference between cursors: △V
    Time difference between cursors: △T
    Reciprocal of △T in Hertz (1/ΔT)
    Auto Measuerment Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF
    Display
    Display Type 7 inch 64K color TFT (diagonal liquid crystal)
    Display Resolution 800 horizontal by 480 vertical pixels
    Display Contrast Adjustable (16 gears) with the progress bar
    Probe Compensator Output
    Output Voltage( typical) About 5Vpp into ≥1MΩ load
    Frequency(typical) 1kHz
    Power Supply
    Supply Voltage 100-120VACRMS(±10%), 45Hz to 440Hz, CATⅡ
    120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ
    Power Consumption <30W
    Fuse 2A, T rating, 250V
    Environmental
    Temperature Operating: 32℉to 122℉(0℃to 50℃);
    Nonoperating: -40℉to 159.8℉(-40℃to +71℃)
    Cooling Method Convection
    Humidity +104℉or below (+40℃or below): ≤90% relative humidity;
    106℉to 122℉(+41℃to 50℃): ≤60% relative humidity
    Altitude Operating: Below 3,000m (10,000 feet);
    Nonoperaring: Below 15,000m(50,000 feet)
    Mechanical
    Size Length 385mm, Width 200mm, Height 245mm
    Weight 3.5KG(with Packing);  2.08KG(without Packing)

     

    3. Other Pictures

4. Standard Accessory:

 

ĐỊNH NGHĨA SẢN PHẨM

- Sản phẩm chính hãng: Là những sản phẩm được đính kèm nhóm từ "chính hãng...", đây là những sản phẩm chính hãng như TI, ST, NS, HANTEK, UNI-T,... Chúng tôi khuyến khích khách hàng mua các sản phẩm này.  Chất lượng sản phẩm tốt và không gặp phải rủi ro khi sử dụng.

- Các sản phẩm khác: Không đính kèm nhóm từ "chính hãng...": Đây có thể là những sản phẩm chính hãng nhưng chưa được cập nhật thông tin, hoặc là 1 sản phẩm like new, refubished, sản phẩm Trung Quốc, .... Việc sử dụng sản phẩm có thể gặp phải rủi ro nhỏ.

- Sản phẩm tháo máy: Là những sản phẩm đã qua sử dụng, trong 1 số trường hợp sẽ được tân trang lại để đảm bảo thẩm mỹ đến tay khách hàng. Việc sử dụng sản phẩm có thể gặp phải rủi ro nhỏ.

ĐỐI VỚI NHỮNG ĐƠN HÀNG COD BỊ HOÀN LẠI

    Đối với những đơn hàng gửi COD (nhận hàng - thu tiền tại nhà) bị hoàn trả lại do lỗi chủ quan của khách hàng như khách hàng đổi ý không mua sản phẩm, đi vắng không nhận sản phẩm được, không nghe điện thoại từ nhân viên bưu chính,... thì chúng tôi sẽ từ chối gửi bằng hình thức COD cho quý khách từ những đơn hàng tiếp theo. Nếu quý khách vẫn có nhu cầu mua hàng qua dịch vụ chuyển phát xin vui lòng thanh toán 100% tiền hàng trước thông qua ngân hàng, sau khi nhận được tiền chúng tôi sẽ gửi hàng theo đơn hàng đã đặt.

0985246260
popup

Số lượng:

Tổng tiền:


zalo
zalo